An Air Barrier systems should:

Air Barrier

- eliminate air movement through the building envelope

- be continuous over the entire building enclosure

- be robust enough to withstand its environment and forces applied

- be durable

Air barrier systems are created in numerous ways:

- exterior air barrier membranes – blueskin used on commercial applications

The advantage to the blueskin membrane is that it self adheres, does not release and is continuous when properly installed.  Its disadvantages include its cost.  It is therefore generally used only in Commercial applications.   Being installed on the exterior of the wall, it does nothing to prevent differential pressure from moving moisture laden air into the wall from the interior of the building.

- Exterior applied rigid foam panels

Exterior rigid foam panels form a continuous insulating layer which when newly and properly installed form an air barrier system that is impenetrable to the effects of wind pressure and resultant heat loss.  The main disadvantage is that the system relies on the resilience of adhesives and sealant caulking which yield over time allowing air movement around the panels.  Rigid Foam Panels do not prevent moisture laden interior air from moving into the wall cavity.

- interior air barrier membranes – 6 mil polyethylene

The main advantage to 6 mil polyethylene sheet is that it is widely accepted and inexpensive.  It also prevents moisture laden air from entering the wall cavity through the interior side of the wall assembly.  The disadvantages is that it is dependant on adhesives and sealants which fail in time and it is subject to penetrations at time of construction and by occupants who hang paintings, or make changes to their interiors.  Because it is applied to the warm side fo the wall assembly in Canada, it does nothing to prevent wind pressure or vapor pressure from moving moisture laden air into the wall cavity from the exterior side of the wall.  Ove rthe life of a building, it performs as a poor air barrier.

- interior air barrier through gypsum board

Gypsum board as an air barrier is a difficult assembly to create because it requires a level of attention to detail that most contractors and tradesmen fail to provide.  Top and bottom plates, rim joists and sub floor, ceiling board, sill plates must all be caulked, glued, taped, or sealed with gaskets prior to installation.  This is an air barrier system which will only perform with extreme attention to detailing as it is installed and therefore generally fails to meet its performance criteria even when just installed.   In time, these sealants release causing drywall to perform as a poor air barrier.

- cavity filled spray foam insulation air barrier

Spray Foam insulation is an effective air barrier system, surpassing the National Building Code of Canada’s specification (the most stringent in the world) with an air permeance of less than 0.02 l/(s-m2) @ 75 Pa.  Acting as an air barrier, vapor barrier and insulation layer in a single application, drying is not a factor as the materials itself is impermeable to moisture.  The main advantage to spray foam is that it is ‘custom fit’ – adhering to and formed specifically for the space into which it is applied.  It requires no detailing or other special care, it never settles, sags, or degrades in performance.

Unlike other air barriers which are designed to protect a fibrous insulating material, insulating foam is not subject to moisture ingress from either the warm or cold side of the wall and thus moisture accumulation and damage is not an issue.  This is a very significant benefit to using foam.  Spray foams main disadvantage is its perceived cost.  While up front it is more expensive, the long term impact on ownership costs result in savings to homeowners who choose spray foam insulation.

Air Barriers are key to the building Envelope, see our next article….. moisture control and the building envelope.

Tags : building envelope, energy efficient, Environment, moisture, spray foam insulation
Posted in : building envelope | 39 Comments »

Your Building Envelope

The Building Envelope: your first

line of defence

The first article in this series identified the importance of a tight building envelope in creating green homes.  Structural Insulated Panels and Insulated Concrete forms create an excellent air tight wall Assembly and building envelope because they do no breathe, have a high resistance to heat loss and create healthy indoor living environments by controlling the flow of moisture and eliminating condensing surfaces on the internal wall surfaces.  However 99% of all homes are built with conventional 2×6 framing.  This article looks at the design of conventional building envelope, the advantages of sealing homes with spray foam insulation and the importance of effective air barrier and vapor barrier control layers.

The building envelope is made up of the roof, above grade walls, below grade walls, and the basement floor.  These building envelope components should be thought of as systems for each is made of an assembly of individual products, working together.  These products include exterior cladding, control layers (moisture barrier, air barrier, thermal barrier) and the structural members (framing).  Each of these components plays an integral role in how a building envelope and the house it encloses performs – the failure of any of them can result in the failure of the building envelope.

Are conventionally built homes satisfactory?  Modern homes are code required to be built with 2×6 structural framing, a minimum of R-20 insulation (thermal barrier) and a layer of 6 mil polyethylene sheet (vapor barrier & air barrier).  There are additional layers to the wall assembly including gypsum wall board, and paint on the interior and OSB, house wrap and cladding on the exterior.

Traditional Building Envelope design: Deficient

The problem with the above building envelope is this:  The entire system relies on the 6 mil polyethylene membrane to stop air movement, vapor movement and to permit the fiberglass batt to perform as designed!  In Canada, the polyethylene layer goes on the warm side of the wall because we are in a climate which predominantly requires heating meaning it is subject to dozens of penetrations at the time of installation (electrical outlets, light switches, window frames and doors, recessed lighting enclosures, seams – top, bottom and where the layer must be installed around framing members.)  This says nothing of the penetrations added with decorative wall hangings, nail holes and modifications done after the fact.  Unless these seams and penetrations are sealed in such a way as they never release, plenty of opportunity for air movement and with it moisture movement is created.  Worse, because fiberglass batt insulation allows air and moisture to move through it, penetrations and deficiencies in the 6 mil poly layer allow for air pressure differences across the wall assembly to degrade the performance of the insulating layer over time resulting in effective R-Values of half (or less) the advertised value.

Spray Foam Insulation creates a lasting high performance building envelope.

If this same building envelope were insulated and sealed with a  single application of spray foam insulation, the result would be significantly different.  Because spray foam is manufactured on site, it conforms to every minute variance, nook and cranny in the building envelope.  It is a perfect, custom made fit.  Made up of billions of tiny, microscopic bubbles, it will never settle, sag, or move, it absolutely and completely seals a wall without any penetrations.  It conforms to electrical boxes, outlets, and recessed light cans, wrapping itself around and behind them to completely enclose them.  It is inches thick and not subject to any of the potential problems of a layer only 6 mil thick.  Spray Foam is not dependant on caulking, glue or sealants to act as an air barrier or vapor barrier and results in a building envelope that is air tight, impenetrable to moisture, and has a stable R-Value much higher than fiberglass.  At an R value of 6 per inch, there is potentially R-33 available in a 2×6 cavity wall if super insulating is required.

Conclusion:

A robust building envelope is designed to endure and separate two different environments.  The modern, conventional building envelope does not do this adequately because it is constructed using an air barrier and vapor barrier subject to degradation over time.  The system created to accomplish this is too heavily dependant on a single layer of thin plastic (6 mil polyethylene), and any penetrations or deficiencies in its installation, or subsequent use degrades building envelope performance allowing moisture into the building envelope and heat loss from it resulting in higher expense and shorter useful life span.  Spray Foam, though more costly at time of installation addresses this in a single, simple application and is required in new homes by informed homeowners.

Our next article will look at the importance, function, design and performance of the air barrier layer and materials used to create air barriers in the building envelope.

Tags : air tight, benifits, building envelope, Environment
Posted in : building envelope | 12 Comments »

Straight talk: Green Building

Green Building Technology

Few terms have  been as abused as Green building.  Today there are green buildings, there is green energy, the green movement, green appliances, technologies and even points (LEED).  What is a green building?  How does one quantify what green building means, define how green buildings are measured, and place a value on the ‘greenness’ of a particular product, technology or service let alone on an entire green building?

Green is the color of the natural world as reflected in our lawns, landscaping and trees.  It is the color of health and vitality and has become a catch all for things good for the earth.  Specifically, green building is a term used to identify technologies that reduce carbon emissions and preserve our planet for future generations.

Green building basics

When it comes to our homes, what makes a green building? Simply put, it is the energy it uses.  Energy production in the United States and Canada is a dirty business.  It does not matter if you are speaking of gas powered electric plants, coal driven energy, natural gas furnaces, heating oil or propane, even nuclear creates troublesome byproducts.  A building therefore is green if it accomplishes the task of providing housing while using less energy than a comparable home or building.

Green building essentials

First, a green building must serve its essential purpose.  A home must provide shelter and be structurally sound, it must prevent rain and snow from entry, it must be fire safe and create a healthy and comfortable indoor living environment.  This is the bare minimum required of any building.  In order to be a green building it must do this while consuming less energy.

Green building priorities: Efficiency or Conservation?

Most green building technologies rave about the benifits of efficiency but this overlooks the more significant gains that can be achieved through conservation.  Before you can efficiently condition (heat or cool) air in a building, you must first enclose it.  The enclosure is more important than all the air handling systems inside it.  Without an air tight building envelope you might as well try to condition the air in a nylon tent – you can’t, no matter how efficient your heat source.

Green Building Options

A good enclosure is one that is air tight and has a high resistivity to heat loss.  There are three building envelope technologies that achieve the highest level of performance; Structural insulated panels (OSB-Foam-OSB sandwich) known as S.I.P.’s, Insulated Concrete Forms (Foam-Concrete-Foam sandwich) known as I.C.F.’s and lastly, conventional framing insulated with spray foam insulation.  You will notice that each of these building technologies utilizes foam and there is a reason for that.  Because foam contains billions of tiny bubbles separated by micro thin plastic walls, it is the very best insulator available and therefore a green building product.  Because it is impervious to air, it acts as an air barrier.  Because it is impervious to water, it is a recognized vapor barrier.   The air barrier and vapor barrier characteristics of foam are perhaps even more important than its high R-Value.  No other material insulates or creates a better building envelope and therefore green building than foam.

Green Building for most of us.

S.I.P.’s and I.C.F.’s require special construction techniques and change the construction process.  Many builders are unfamiliar with these.  Because 99% of residential homes still use conventional framing, spray foam is a much more readily available option for homeowners who want a green building.  Building with one of these envelope technologies results in tight building envelopes and energy efficient homes.  This is the real green.

Future articles in this series will explore these key areas in greater depth:

- Building envelop design

- Effective Air Barriers

- Moisture and the building Envelope

- The effect of glazing

- Building Orientation & Glazing

- Efficient air conditioning systems

- Green building details

Tags : building envelope, Environment, spray foam insulation
Posted in : Environment | 7 Comments »